Jump to content

  • Welcome to Auto Parts Forum

    Whether you are a veteran automotive parts guru or just someone looking for some quick auto parts advice, register today and start a new topic in our forum. Registration is free and you can even sign up with social network platforms such as Facebook, X, and LinkedIn. 

     

Points for attention to replace pumps


Recommended Posts

When the pump is damaged, we should pay attention to the following items when replacing.

(1)   The real cause of the pump damage should be clear. Before replacing the pump, the radiator fan, thermostat and coolant should be determined.

(2)   It is likely that pumps with similar shapes but suitable for different types of engines will occur, so before installing the pumps, a comparison should be made between the new pump and the old pump removed, or a check should be made on the part number of the pump and the type of the engine to determine whether the selected pump is suitable for the model being repaired.

(3)   Water pump installation surface should be carefully cleaned and leveled.

(4)   When installing the pump, wet the seal ring with coolant first. If you need to use sealant, be careful not to apply too much.

(5)   Do not use the way of percussion pump shaft to install the pump. You should check the real reason for the difficulty of pump installation. If the excessive scale in the cylinder water channel leads to the difficulty of pump installation, steel wire brush or fine sand paper should be selected according to the scale situation. When installing bolts in water pumps, they should be tightened progressively in the direction of diagonal according to the prescribed torque, excessive tightening of bolts or causing damage to gaskets.

(6) The tension of the pump belt must be strictly controlled according to the adjustment standard. Excessive tension of the belt, will cause bearing overload operation and early damage; and too small tension, easy to produce noise, serious pump can not work properly.

Feilong Jiangli warm notes: If you can't replace it by yourself, please go to the warehouse.

Edited by Mengjuan Zhu
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

  • Similar Topics

    • By NAPA
      Brad Sweet and the
      link hidden, please login to view No. 49 team had high expectations for a Kansas swing with High Limit Racing, starting with a  mid-week show scheduled for Wednesday at 81 Speedway in Park City, KS. But after severe storms crossed the area Tuesday night and forced a cancelation, the team looked ahead to Lakeside Speedway in Kansas City for two nights of High Limit Racing action at Shane Stewart’s Heartland of America Showdown. With NASCAR in town at Kansas Speedway just a short drive away, Lakeside was buzzing with racing fans on Friday night. In qualifying, Sweet made his mark in the NAPA No. 49, hitting the charts in fourth with a time of 15.354 seconds. After starting on the pole of his heat race, the Big Cat maintained his position to the checkers and secured his spot in the dash.
      The NAPA team came up with a sixth-place starting position for the dash after Sweet’s spin of the wheel, and the No. 49 team had seven laps to improve their starting position for the evening’s feature.  A strong start allowed the No. 49 to jump to fifth, and Sweet finished in that spot to earn a fifth-place start in the feature. The enthusiastic crowd was in for a treat with the main event. Sweet and the NAPA team showcased their skills as the No. 49 surged through the field. The Big Cat had the best car setup on track, and he swiftly made his way to the front before clinching his third High Limit Racing win in the Lakeside thriller.
      With Friday night’s win under his belt, Sweet wasn’t required to make a qualifying run on Saturday; he was locked into heat race action ahead of Saturday’s $50,000-to-win main event. With the pressure on, the No. 49 was second across the line after starting the heat race in fourth, again locking Sweet in to the dash. A spin of the wheel put him eighth to start.
      Despite tough competition, the Big Cat picked up two spots in the dash, placing the NAPA team sixth to start the 30-lap, final race of the Heartland of America Showdown. A $50,000 payday awaited the winner, and Sweet and the No. 49 team were determined to cash in. Sweet again found his NAPA machine to be a rocket on the Lakeside Speedway dirt. He blazed through the competition and held off Kyle Larson to surge from sixth to first. Taking the checkered flag for his second-consecutive win of the weekend,  Sweet secured the $50,000 grand prize and took over the High Limit Racing points lead.
      Start / Finish:
      Friday, May 3: 5 / 1
      Saturday, May 4: 6 / 1
      Points Standing / Total: 1st / 816 pts. (+8)
      Next Race: Friday, May 10, 34 Raceway, West Burlington, IA
      How to Watch or Listen: 
      link hidden, please login to view NAPA: 
      link hidden, please login to viewBrad Sweet:  link hidden, please login to view
      Kasey Kahne Racing:  link hidden, please login to view The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • By NAPA
      Christian Eckes took the NASCAR CRAFTSMAN Truck Series points lead on Friday night with a stout fourth-place performance at Texas Motor Speedway. The driver of the No. 19 Gates Hydraulics Chevrolet Silverado RST captured his third top-five finish of the season and scored 50 points on the night, the second-most of all drivers in the field. Eckes led 31 laps, the only driver to have led laps in each race this season, and tallied his third top-five finish in the last four events.
      For the second-consecutive weekend, Eckes qualified on the front row and was a mainstay in the top five for the entire event. He settled into second at the drop of the green flag and challenged for the lead near the midway point of the opening stage. The first lead change of the night occurred when Eckes powered his Gates Hydraulics Chevy to the lead on lap 17 and paced the field for 21 circuits. He surrendered the lead on lap 38 and collected nine points at the end of Stage 1 on lap 40 while running second.
      Crew chief Charles Denike brought Eckes to pit road under the stage caution for four fresh tires, fuel, and a minor air pressure adjustment to tighten his balance. Eckes restarted second on lap 47 and maintained position inside the top five for the ensuing 35-lap run. An improved handling balance and consistent lap times netted Eckes another eight points at the end of Stage 2 on lap 80 by running in third position.
      Eckes was armed with another batch of fresh tires, fuel, and minor adjustments to fine-tune the handling during the second stage caution. After restarting third on lap 87, he waged war for the runner-up position and gained control of it by lap 100. He ran there until a cycle of green flag pit stops began on lap 119. Eckes made his final stop on lap 129 just before a caution waved. He was able to stay on the lead lap in fourth position and in contention for the victory. He made another fierce run for the race lead on a lap 150 and led until lap 158. During the final 10 laps, Eckes fought valiantly for one final charge at the lead but took the checkered flag in fourth position for his third top-five and sixth top-10 of the season.
      “Not a bad points night,” Eckes said. “I thought we’d have a pretty good shot at the win there, but just went down into Turns 1 and 2 and got way too tight and slid up the racetrack. It is what it is. I’m proud of the No. 19 Gates Hydraulics team for making the improvements that they did. Our mile-and-a-half stuff has definitely shown a little bit of an improvement. We still have a little bit of a ways to go, but we’ll see how it goes.”
      Start / Finish: 2 / 4
      Points Standing / Total: 1 / 287 pts. (+2)
      Next Race: Saturday, May 4, Kansas Speedway
      How to Watch or Listen: 8:00 p.m. ET on FS1, MRN or SiriusXM
      NAPA: 
      link hidden, please login to view
      Christian Eckes:  link hidden, please login to view
      Bill McAnally Racing / McAnally-Hilgemann Racing:  link hidden, please login to view The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • By Counterman
      The water pump is a vehicle component that needs no introduction. For most vehicle owners, however, they don’t think about it until something goes wrong.
      As the only moving part of the cooling system, the water pump plays a vital role in keeping the vehicle running optimally in all weather conditions. Water pumps usually last a long time – 100,000 miles or more on average. When a water pump fails, though, the results can be catastrophic for the engine.
      Let’s talk about some common causes of premature water-pump failure.
      Coolant Contamination
      Coolant can become contaminated with dirt, debris or other substances that can wear down the water pump’s internal components, including the seals and bearings. This contamination can accelerate wear and lead to early failure.
      Cavitation
      This phenomenon occurs when vapor bubbles form in the coolant near the pump’s impeller blades, causing shock waves when they collapse. Over time, this can lead to pitting and erosion of the impeller blades, reducing the pump’s effectiveness.
      Improper Coolant Mixture
      Many water-pump failures are caused by factors other than a faulty pump. Using the wrong coolant mixture or water-to-coolant ratio can cause corrosion and deposits within the pump, reducing its efficiency and lifespan. Additionally, incorrect coolant types can chemically react with pump components, causing deterioration.
      Bearing Failure
      Bearings within the water pump allow the impeller to spin smoothly. Over time, these bearings can wear out or fail – often due to tension from a misaligned or overtightened belt – leading to noise, leaks or a seized pump.
      Thermal Stress and Fatigue
      Constant exposure to fluctuating temperatures can cause the metal components of the water pump to expand and contract, leading to stress fractures and eventual failure.
      Leakage and Seal Failure
      The water pump’s seals are prone to wear and degradation over time, leading to coolant leaks. Such leaks not only reduce the efficiency of the cooling system but also can cause overheating and further damage to the water pump and surrounding components.
      Warning Signs
      Recognizing the early signs of water-pump failure can prevent more significant engine damage. Here are some key indicators:
      1. Coolant leak – One of the most straightforward signs is a coolant leak at the front of the vehicle, typically near the center. This can indicate a failed seal or gasket in the
      water pump.
      2. Overheating engine – If the water pump isn’t circulating coolant effectively, the engine temperature can rise, leading to overheating. Persistent overheating, especially under normal driving conditions, should prompt an inspection of the cooling system, including the water pump.
      3. Strange noises – A failing water pump can produce a variety of noises, such as whining or grinding, often due to bearing failure or an impeller rubbing against the pump housing.
      4. Steam from radiator – Seeing steam emanate from the radiator is a clear sign of overheating, which could be due to a malfunctioning water pump.
      5. Corrosion and deposit build-up – Visible corrosion or significant scaling on the water pump or surrounding components can indicate a failing pump, often due to improper coolant use or leaks that allow air into the system.
      While the service life of most OE water pumps should be 100,000 miles or longer, a cheap replacement pump might not make it 30,000 miles before it starts to leak. To keep your customers happy, it’s always a good idea to recommend a well-built, high-quality water pump from a trusted manufacturer. And when they’re replacing the water pump, you’ll want to check if they need any gaskets, hoses, coolant, belts or a thermostat. 
      Also, if your customer who just purchased a new aftermarket water pump from you doesn’t flush the system and use new coolant when they install the new pump, there’s a good chance you’ll be hearing from them sooner rather than later with a warranty return. You should encourage your customers to follow the vehicle’s recommended flush-and-fill schedule, and to always use the coolant specified by the vehicle manufacturer. Most coolant suppliers do not recommend intermixing different brands or types of coolant in the same cooling system, due to the risk of coolant-gelling, corrosion or abrasion of water-pump seals.
      The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • By Counterman
      Carter has expanded its line of electrical auxiliary water pumps to include three new part numbers tailored specifically for Tesla vehicles.
      “With a focus on meeting the unique demands of Tesla vehicles, these auxiliary water-pump SKUs are engineered to efficiently move fluid in high-temperature environments, keeping pace with the rapidly evolving technologies found in modern engines,” the company said in a news release.
      The new part numbers cater specifically to Tesla models, complementing Carter’s comprehensive range of water pumps that already cover 95% of domestic and import VIO,
      link hidden, please login to view noted. The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • A-premium Auto Parts:5% OFF with Code GM5.
    • By NAPA
      Chase Elliott and No. 9 Kelley Blue Book team qualified third for Sunday’s NASCAR Cup Series race at Phoenix Raceway The 28-year-old driver earned valuable stage points, finishing fifth in stage one and seventh in stage two A slew of cautions in the final stage prompted multiple strategies among teams. Elliott restarted 17th after the final caution of the race and ultimately finished the race in the 19th position Elliott and the No. 9 team leave Phoenix ninth in the Cup Series points standings After posting the seventh fastest lap in Friday afternoon’s NASCAR Cup Series practice session at Phoenix Raceway, Chase Elliott backed that up with a third-place qualifying lap on Saturday. The 28-year-old driver took the green flag for the 312-lap race from the second row on Sunday afternoon. Elliott was still running inside the top five when the first caution flag of the race waved on lap seven. The early report from the Hendrick Motorsports driver was that his No. 9 Kelley Blue Book Chevrolet Camaro ZL1 was locked down and tight in the back. With the team opting not to pit, Elliott restarted in the fifth position on lap 12 and remained there as the rest of 60-lap first stage went caution free. The fifth-place stage finish garnered six stage points for the Dawsonville, Georgia, native.

      Under the stage-ending caution, Elliott relayed to crew chief Alan Gustafson that the Kelley Blue Book Chevy was tight and that it freed up as the run went on. The crew opted for four tires, fuel and a chassis adjustment during a fast pit stop which gained Elliott a spot on pit road. He lined up fourth to start the second stage on lap 69. Elliott raced three-wide once the field went back to green, taking over the third position on lap 70. He held strong, maintaining his top-three running position through a long green-flag run. The field started making green-flag pit stops on lap 115, with Elliott bringing the Kelley Blue Book Chevrolet to pit road on lap 117 for four tires and fuel. With the field stretched out, Elliott was bogged down in traffic following his stop, making it harder to gain track position. Still, he managed to score a top-10 finish in the second stage, taking the green-and-white checkered flag in the seventh spot. The result added four more stage points to his total. 

      During the stage break, Elliott brought the Kelley Blue Book Chevrolet to pit road for four tires and fuel. The pit crew knocked out another fast stop, gaining the 2020 Cup Series champion three spots. Elliott took the green flag for the final stage from the fourth position on lap 194 and was scored in fifth place when the caution came out just two laps later. Elliott kept his Chevrolet on the track under the yellow flag. He lined up fifth for the restart on lap 202 and was battling inside the top 10 when the race was slowed once more. Staying out while some drivers deeper in the field visited pit road, Elliott restarted eighth and was scored in ninth at the time of the lap-216 caution. Gustafson called Elliott to pit road with the rest of the leaders for four tires, fuel and a chassis adjustment. With varying pit strategies among teams – some taking only two tires and others opting to stay out – Elliott restarted in the 17th position on lap 220. He managed to advance as high as 16th early in the run but being stuck in dirty air made it difficult for Elliott to continue forward progress. When the checkered flag waved on lap 312, he was scored with a 19th-place finish.

      Elliott and the No. 9 team leave Phoenix Raceway ninth in the Cup Series points standings, just 28 markers behind the leader.
      Start / Finish: 3 / 19
      Points Standing / Total: 9th / 123 pts. (-26)
      Next Race: Sunday, March 17, Bristol Motor Speedway
      How to Watch or Listen: 3:30 p.m. ET on FOX, PRN or SiriusXM
      NAPA: 
      link hidden, please login to view
      Chase Elliott:  link hidden, please login to view
      Hendrick Motorsports:  link hidden, please login to view
      No. 9 Team:  link hidden, please login to view The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view

×
  • Create New...