Quantcast
Jump to content

  • Welcome to Auto Parts Forum

    Whether you are a veteran automotive parts guru or just someone looking for some quick auto parts advice, register today and start a new topic in our forum. Registration is free and you can even sign up with social network platforms such as Facebook, Twitter, Google, and LinkedIn. 

     

Recommended Posts

When calculating the scale of the oil scale, it is best to choose the flange face of the ruler tube. The reason why the flange is chosen as the measuring reference is that the ruler's position in the engine is completely determined by it.

image.png.44266ce966aadca358a9acc1baba30f2.png

(1) B is the length of the axis of the ruler. After the scale tube is arranged on the engine, it can be directly measured from the digital module.

(2) C is the length of the ruler tube inserted into the flange installation surface. The length is set according to the length of the ruler. If the condition is allowed, it is best to keep the ruler to protect the head of the ruler, so that the measuring head of the ruler is parallel to the wall of the ruler, and the scraping of the scale section of the ruler is reduced.

(3) D is the value from the flange surface to the maximum scale, corresponding to L1 in Figure 6. Similarly, the value from the flange surface to the minimum scale is L2.

It is easy to get the theoretical distance of the ruler: the distance between the handle of the ruler and the mouth of the ruler to the maximum level of the level of the level of the level of the oil level: AMAX=B-C+L1, the same, the distance between the yardstick and the ruler's pipe mouth to the minimum level of the level of the level of the oil level: AMIN=B-C+L2.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Flora Fan VSPZ Bearing
      Hello Everyone
      I am Flora from Shandong Wo Si Huo Te Machinery Equipment Co., Ltd, a professional manufacturer of wheel hub bearings,
      clutch release bearing, tensioner pulley, ball bearings, roller bearing and other automotive bearings.
      Our factory is founded in 2004, which has over 10 year's experience. We are reliable supplier of VBF and GPZ.
      Feel free send email to [email protected] or Add WhatsApp: +8615953177833
      😃😃😃



    • By MaXpeedingRods
      Buying a turbocharger for your car can sometimes be a daunting and confusing task. At maxpeedingrods.com, it is our mission to make that task as an easy and painless as possible. This Buyer's Guide is designed to answer any questions you may have during your search for the right turbocharger for your car, and how to buy a turbocharger on our website.
      WHAT IS A TURBOCHARGER?
      A turbocharger(turbo)is a turbine-driven forced induction device that increases an internal combustion engine’s efficiency and power output by forcing extra air into the combustion chamber. When a turbocharger brings more air into the chamber, it gets mixed with more fuel, yielding more power as a result. It smuggles air by compressing it using the energy of the exhaust gasses coming out of the engine.
      HOW DOES A TURBOCHARGER WORK?
      How does a turbo work in a car engine? It applies almost the same principle of a jet engine. It has two main parts – a turbine and a compressor. When one part spins, the other spins with it too because they are linked to each other. Exhaust gasses blast out of the engine when the fuel burns inside the combustion chamber. The gasses go down into a tube and wind the turbine, which rotates at significantly high speeds and causes the compressor (which is actually a turbine in reverse) to spin. This chain of action siphons more air into the engine cylinder, allowing burning more fuel and producing more power each second.
      HOW TO BUY A TURBOCHARGER?
      Correctly identifying the turbo means you'll get the right replacement first time, saving you time, money and hassle. In order to supply the correct turbo for your vehicle, we will always ask you to supply the part number from the Turbocharger either directly from the Turbocharger itself or by contacting your vehicle dealer to get the OEM part number from them. Most part numbers can be found on the name- plate of compressor housing, as shown below.
      • Finding the right part number with GARRETT turbochargers.
      • Finding the right part number with IHI turbochargers.
      • Finding the right part number with KKK turbochargers.
      • Finding the right part number with Mitsubishi turbochargers.
      • Finding the right part number with HOLSET turbochargers.
      • Finding the right part number with SCHWITZER turbochargers.
      You can contact one of our turbo specialists at https://www.maxpeedingrods.com/ for further assistance on how to buy a turbocharger.
      WHY BUY TURBOCHARGERS AT MAXPEEDINGRODS?
      MaXpeedingRods has been engaged in the research of overseas racing products and culture for decades. If you are looking for turbochargers, you have landed at the right place. On the basis of your vehicle make and model, you can choose from a plethora of automotive maintenance and accessories. MaXpeedingRods offers a seamless online shopping experience and the streamlined e-commerce interface makes it easy for you to find just the turbocharger you want.
      MaXpeedingRods offers a variety of turbochargers in both Sport performance and Street performance.
      Turbocharger—Sport performance • Stainless steel volute with high temperature resistance 1050 degree Celsius
      • Aluminum blades with CNC precision machining forging
      • Imported movement bearing and precise dynamic balance support maximum pressure 3.0bar Water-cooled structure greatly extends turbine life
      • The corresponding horsepower range is 300—850
      Turbocharger---Street performance • High nickel alloy shell with high temperature resistance 850 degree Celsius
      • Imported floating bearing structure and precise dynamic balance
      • Aluminum blades with precision machining forging
      • The corresponding horsepower range is 200-600
      For professional assistance, you can reach out to us via our websitehttps://www.maxpeedingrods.com/

      WHAT ARE THE SIGNS THAT MY CAR NEEDS NEW TURBOCHARGER?
      Turbos are supposed to be long-lasting, however, it is still possible that some damage may happen over time. If you’re wondering whether your vehicle needs to have the turbocharger replaced, look for the following 5 signs:
      1. Slow Acceleration The primary function of a turbo is to make your car more powerful. One of the first noticeable symptoms is a lack of power and slow acceleration. If you notice that it doesn’t accelerate as fast as it used to, the first thing you should consider checking is the turbo.
      2. Burning Oil Burning excessive amounts of oil is typically a sign of a turbo failure. Locate the downpipe, at the front of the turbo, and disconnect it. You can look inside the turbine by using an endoscope; if there is oil inside, that’s a sign of gradual failure. You should resolve the problem as soon as possible; if left untreated, your turbo will eventually fail.
      3. Excessive Exhaust Smoke If the turbo housing cracks and or if there are worn internal seals, this may lead to oil leaking into your exhaust. As the oil burns off you will see a distinct grey or blue smoke. This symptom is more apparent when the turbo is in use. So if you notice smoke when you rev your engine, it could be a sign of a faulty turbo.
      4. Check Engine Light or CEL On most modern cars, the computer diagnostics will detect a failing turbo resulting in the “check your engine.” With that said, the CEL is displayed for a number of problems, sometimes it warns us of a loose gas cap and sometimes about far more serious issues. One of those more serious issues could be the turbo. It’s best to have a mechanic look at your vehicle if the CEL is displayed.
      5. Loud Whining Noise When the boost is running, a failing turbo could make a loud whining noise. The noise usually sounds like a siren, and it tends to get louder as the problem aggravates. If you notice an unusual noise paired with some of the above symptoms, your turbo might be failing. When a turbo becomes faulty, there are plenty of warning signs. They are often audible or they offer visual queues. Ensure at each servicing that you have your oil changed to avoid carbon deposits. If your turbo is older, consider having it replaced. If you aren’t experienced with vehicle components, have a licensed mechanic diagnose the problem.

      HOW TO INSTALL A TURBOCHARGER IN A CAR?
      Have you ever wanted to know how to install a turbocharger, but the task seems too daunting? Don’t wait to upgrade your turbo! Let expert mechanics at MaXpeedingRods help with this step by step guide.
      Step 1: Unplug the green hose from the compressor intake duct. Remove the intake duct and crankcase breather.
      Step 2: Remove the boost control module from the front of the x-section pipe.
      Step 3: Remove the temperature sensor wires from the front of the x-section pipe.
      Step 4: Unplug any remaining hoses and electrical connections from the x-section pipe.
      Step 5: Loosen hose clamps and remove the x-section pipe from the engine. Cover intake manifold openings to prevent foreign objects from entering the pipework during this installation.
      Step 6: Using a 7/16” deep-well socket, loosen turbine outlet v-band clamp and move clamp off of the flange. Separate down-pipe from turbo.
      Step 7: Using a 7/16” deep-well socket, loosen turbine inlet v-band clamp & move the clamp off the flange. This is the most difficult step of the installation. Use penetrating oil to help loosen the clamp.
      Step 8: Reach under turbo and slide the clip on the EBPD control rod towards the pedestal to free the EBPD crank.
      Step 9: Remove the 2 bolts holding the turbo to the pedestal and unplug the red pressure line from the actuator.
      Step 10: Make note of the turbo’s position and how it fits on the engine for future reference. Lift the turbo off the pedestal and remove from the vehicle.
      Step 11: Remove the backpressure valve assy from the old turbo and install on the new turbo. Use anti-seize compound on the threads & torque the bolts to 185 - 215 lb-in.
      Step 12: Ensure the supplied oil inlet and outlet o-rings are properly seated on the pedestal. The turbo oil drain hole will pilot on the raised sleeve. NOTE: Before installing turbocharger, inspect and remove all foreign material from turbo air inlet, exhaust inlet, & exhaust manifold.
      Step 13: Install new turbo.
      NOTE: Turbine inlet flange should line up with the mating exhaust flange. The pin in the Yflange should mate with the hole in the turbine housing flange.
      Step 14: Ensure the crank pin for the EBPD drops into the hole in the control arm rodend. Slide retaining clip back into place ensuing the clip fits into the crank pin groove.
      Step 15: Install and tighten 2 turbo “hold down” torque to 35-37 lb-ft.
      Step 16: Position and install turbine inlet v-band clamp and torque to 110-130 lb-in.
      Step 17: Install downpipe. Guide the v-band flange to mate with the turbine discharge flange. Install v-band clamp & torque to 110-130 lb-in.
      Step 18: Remove covers (rags in this picture) from the intake manifold openings. Re-use the original compressor discharge o-ring and mount it into the new compressor discharge groove. A light coating of RTV or grease can be used to hold it in place.
      Step 19: Position the x-section pipe in place and re-install hoses. Tighten compressor discharge v-band clamp to 110-130 lb in. Tighten hose clamps to 50-60 lb-in, and re-install all electrical and temperature connections.
      Step 20: Re-install the red wastegate hose onto the wastegate hose actuator.
      Step 21: Double check that the compressor inlet area is free from any foreign objects and that the inlet hose is clean. Install the new compressor 4-inch inlet hose in place and insert the green hose into the boss. Tighten clamps snugly.
      Step 22: Re-install the crankcase breather assy, again verifying that everything is clean.
      Step 23: Re-install the hose from the breather duct to the air filter housing, snug the clamps. Reconnect battery, and you’re done!
      Step 24: Now retrace your steps to verify that everything has been re-installed, re-tightened or re-connected and that there are no loose wires, hoses, or fasteners. Make sure that you have retrieved all rags, tools, etc. from the work area. DO NOT OPERATE the engine without the inlet ducting in place.
      Step 25: Start engine and watch for signs of oil leakage at the turbo/pedestal joint. If none exists, drive the vehicle a short distance to fully warm the engine and then re-inspect. Investigate any unusual noise or condition.
      Step 26: If all checks out, then there is no further break-in necessary and the vehicle can be driven as usual.
    • By Yu Billy
      OE NO:038109101R
      Name:camshaft
      Brand:Borsehung

      Applicable models of Borsehung 038109101R
      SKODA:
      FAB 02-04;05-08;07-10/OCT 01-11;04-08;09-13/RO 06-10/SUP 02-08;08-13
      VW:
      BE 99-10/BEC 03-10/BO 02-05/CA 04-11/CAMP 04-10/GOLF 98-09/GOPL 05-09/IMD 08-/JE 06-10/PA 97-11/PASY 97-99/PO 05-10/SHA 96-10/TOU 03-10/TR 03-10
      AUDI:
      A3 01-13/A4 99-01/A4Q 99-05/A6 98-05/A6Q 02-05
      SEAT:
      AL 01-02;03-05;06-08;09-10/ALT 04-06;07-10;11-13/CO 03-05;06-09/IB 02-05;06-10/LE 00-01;02-06;06-10;11-13/TO 99-01;02-04;05-09
      Borsehung 038109101R, a pure OE product with superb quality and a very competitive price, is now in ample supply. Welcome to place an order!
      Contact us
      Purchase link: https://www.borsehung.de/en/service-form/
      Email: [email protected]
    • By Yu Billy
      Function of 8V0698151/5QD698151
      8V0698151/5QD698151 is the most crucial safety part in the braking system. The result of all braking operations is determined by the braking pad.
      Common faults of 8V0698151/5QD698151
      1. Abnormal sound is often heard during braking.
      2. During high-load braking, the braking pad is prone to deformation due to severe wear under high temperature. In serious cases, a braking operation may fail.
      Reference NO: 8V0698151/5QD698151
      Name: Brake Pad Set, disc brake
      Brand: vika

      Applicable models of vika 8V0698151/5QD698151
      SKODA: OCT13-
      VW: GO13-14
      AUDI: A3 13-15
      SEAT :LE13-16
      Advantages of vika 8V0698151/5QD698151
      1. Thermo-stable: The refractory ceramic material is able to tolerate a temperature up to 650℃ during continuous braking operations. At high temperatures, this pad provides excellent braking without any deformation or melting. With a high braking torque, it helps shorten the braking distance.
      2. Dust-free: The advanced ceramic material reduces accumulation of dust effectively, and avoids development of rust or corrosion.
      3. Low noise: The beveled-edge design helps eliminate abnormal sound, and matches the braking disc perfectly, causing no harm to the latter.
      When should 8V0698151/5QD698151 be replaced?
      1. Visual inspection: A new braking pad typically measures about 15mm in thickness. If you discover through visual inspection that the pad is merely 5mm thick, it’s time to change it.
      2. Sound: If during a gentle braking process a hissing sound like that generated by iron pieces rubbing against each other is heard, the braking pad should be replaced without delay;
      3. Force required for braking: When the brake is pressed, if it feels less resistant than usual or shows dangerous insensitivity, the pad should be replaced.
      With a unique technical design, vika 8V0698151/5QD698151 reduces braking noise effectively, and provides a long service life due to excellent durability. Welcome to contact us for purchase.
      Contact us:
      Purchase link: http://www.tantivy.com/?page_id=2194&lang=en
      Email: [email protected]
    • By Sanly Wen
      Guangzhou Tomoi Auto Parts Co., Ltd. is located in Auto City, Guangzhou, China. We are a professional manufacturer of auto steering and suspension parts. We focus on producing tie rod end, rack end, stabilizer link and ball joints, and offering reasonable price and on-time delivery. With more than 30,000 square meter factory area, we currently have developed more than 1500 molds for Japanese, Korean and American vehicles. Our main features are listed as below.
      1) Under IATF 16949 standard
      2) Japanese 5S standardized workshop management
      3) strict manufacture and inspection processes
      4) apply special patent technology
      5) over 16 years R&D experience
      6) On time delivery and large output capacity
      7) OEM service offered,customer label accepted
      For more details and brochure, pls feel free to contact [email protected]
  • Similar Topics

    • By RockAuto
      Get up to $30 back when you purchase Mobil 1 motor oil.
      View on RockAuto.com
    • By zafarrafiq
      Best NOCO GB40 Boost Jump Starter 
      Our motive is to show you actual product information which is relay on fact and figures. 
      The NOCO GB40 is a top best and cheap compact, yet powerful 1000 Amp lithium-ion jump starter that deliver 7000 Joules of starting power. Its patented safety technology features spark proof technology and reverse polarity protection making it safe for anyone. Which allow it to safely connect to any battery An ultra-bright 100 lumen LED flashlight with 7 light modes, including SOS and Emergency Strobe Recharge your personal devices on the go, like smartphones, tablets, e-watches and more – up to 4 smartphone recharges Designed for gas engines up to 6 Liters and diesel engines up to 3 Liters Includes GB40 jump starter, 40-inch USB cable, 12V car charger, drawstring storage e bag, and 1-year limited warranty.
      About GB40. The NOCO Genius® Boost™ GB40 is an ultra-compact and portable lithium-ion jump starter for cars, boats, motorcycles, ATVs, lawn mowers, RVs, tractors, trucks and more. It’s extremely safe for anyone to use. It features spark proof technology and reverse polarity protection. The GB40 can instantly jump start most single battery applications, up to 20 times on a single charge. The GB40 is also equipped with a USB battery pack and LED flashlight, making it the ultimate emergency tool.
      KEY FEATURE
               A lithium battery jump starter rated at 1,000 Amps (7,000 Joules3S)
      ·         Spark-proof connections and reverse polarity protection
      ·         Recharges USB devices, like smartphones, tablets, and more
      ·         100 lumen LED flashlight with multiple modes, including SOS
      ·         Jump starts gas engines up to 6 liters, and diesel up to 3 liters
      ·         Provides up to 20 jump starts on a single charge.
      Specifications
      ·         Starting Current: 1,000 Amps Peak
      ·         Joules 3S Rating: 7,000 J3S
      ·         Battery Types: 12 Volt Lead-Acid Batteries
      ·         Internal Battery: 24 Watt-Hour Lithium Ion
      ·         USB Output: 2.1 Amps
      ·         USB Input: 2.1 Amps
      ·         Gas Engine Rating: 6.0 Liters
      ·         Diesel Engine Rating: 3.0 Liters
      ·         LED Flashlight: 100 Lumens
       
      Connecting to the Battery.
      Before connecting to the battery, verify that you have a 12-
      volt lead-acid battery. The GB40 is not suitable for any other
      type of battery. Identify the correct polarity of the battery
      terminals on the battery. The positive battery terminal is
      typically marked by these letters or symbol (POS,P,+).
      The negative battery terminal is typically marked by these
      letters or symbol (NEG,N,-). Do not make any connections
      to the carburetor, fuel lines, or thin, sheet metal parts. The
      below instructions are for a negative ground system (most
      common). If your vehicle is a positive ground system (very
      uncommon), follow the below instructions in reverse order.

    • By APF
      When selecting parts for a car repair, it pays to know the differences between original and aftermarket parts. Whenever possible, get estimates for both.

      Choosing between original and aftermarket car parts — and even used parts of either type — is all about squaring your priorities with your budget.
      You’ll have different options depending on the part and the shop. And the best choice will depend on whether you’re trying to keep repairs cheap, restore your car’s appearance after a wreck or soup up your ride.
      » SIGN UP: Find savings on your car expenses
      Before we get into that, here are the key differences:
      Original equipment manufacturer (OEM) parts match those that came with your car, and are of the same quality as its original parts. They’re also the most expensive. Aftermarket parts are cheaper, and made by other manufacturers — often several, giving you more options. Used parts may have a bit of wear and tear, but should be inspected or rebuilt to ensure they’ll work. These are the cheapest option. Choosing between aftermarket and OEM parts
      Your decision will depend on the type of repair and the quality and price of the parts. Always look for parts that come with a warranty, even if they’re OEM, so you’ll be protected in case they fail.
      Auto body repairs
      Some aftermarket parts may be OK for auto body repair, but others won’t be as good, says Michael Calkins, manager of technical services at AAA. “There’s a lot of variation in quality.” For example, he says, aftermarket parts often don’t have the same level of rustproofing as original parts, fit and finish don’t match, or panels don’t align properly.
      If OEM parts are used in auto body repair, the car should look and work exactly as it did before the damage, because everything will match up. OEM parts are also crash-tested, unlike many aftermarket parts.
      Aftermarket parts come at varying price points and levels of quality, but because they are cheaper, insurance companies often prefer them. If you want OEM parts but are dealing with an insurer that wants the shop to use aftermarket parts, ask to pay the difference.
      “There’s also the option of used parts, depending on the age of the vehicle,” Calkins says. “It may be cheaper than an aftermarket part but still have all of the original quality.”
      Mechanical repairs
      A used part, whether it’s OEM or aftermarket, can really save money on repairs under the hood, so long as it’s inspected first and warrantied. And some aftermarket companies reverse-engineer their products to be even better than OEM versions.
      For example, many car buffs will tell you that you can get heavy-duty shocks and struts or brake pads that are made of stronger materials. Scan some reviews online, or talk with your mechanic if you’re not sure whether an aftermarket part could be an upgrade.
      Adding some extras
      If you’d like to modify your ride by adding something like a backup camera or back-seat TV screen, you’ll probably be looking for aftermarket parts. Certain aftermarket upgrades could increase your car’s resale value. This is especially true for improvements like a better sound system or alloy wheels, rather than mechanical repairs.
      Who provides OEM or aftermarket parts?
      The options you’ll have for parts depends on the nature of the repairs and what type of shop you take your car to:
      Dealership repair shops will offer only OEM parts — they have no reason to offer a cheaper product from a competitor Independent mechanics may be able to offer you a choice between OEM and aftermarket parts Independent garages that specialize in your type of vehicle will likely have both, but with quicker access to OEM parts, including used OEM parts, which can really save you Auto body shops can offer both, but if your collision repair is part of an insurance claim, the insurer will likely prefer aftermarket parts to save money Depending on the job, the cost of OEM versus aftermarket parts varies. Whenever you’re given the choice, ask to see estimates for both so you can weigh your options.
      Source: https://www.nerdwallet.com/blog/loans/auto-loans/oem-vs-aftermarket-parts-car-choose/
    • By RockAuto
      Bosch is offering a 15% instant rebate on select Air, Fuel and Oil Filters
      View on RockAuto.com

×
  • Create New...