-
Welcome to Auto Parts Forum
Whether you are a veteran automotive parts guru or just someone looking for some quick auto parts advice, register today and start a new topic in our forum. Registration is free and you can even sign up with social network platforms such as Facebook, X, and LinkedIn.
PRT Offers Complete Struts For 2019 Honda CR-V
-
Similar Topics
-
By Counterman
Ask anyone what a “complete” brake job is and you’re likely to get a variety of answers. In the context of professional automotive repair, I define complete as meaning correctly done.
Why? Because the actual work that needs done to any given vehicle can vary depending on vehicle mileage, age and condition. And it can vary based on the equipment. For example, do you have access to a brake lathe? As a counter professional, you’ll have to dig into the details with your customer to determine what they need. However, there are simple guidelines to follow that will ensure you’re advising a “complete” brake job every time.
Brake Fluid, Brake Fluid, Brake Fluid
Above all, clean brake fluid is my first requirement.
It’s probably one of the most overlooked vehicle services, and most people don’t think of it as part of a brake job. It’s an afterthought only considered if they’re forced to do it. Anytime I perform brake work, the first part of the inspection is the bleeder screws. They must be able to open. No brake job is complete without flushing the brake fluid.
There’s no need to get “crazy” with it either when it’s done on a regular basis. A couple small 12-ounce bottles are plenty. Use a clean suction-bulb to remove as much brake fluid as you can from the master-cylinder reservoir, refill it, then flush fluid through until you can fit the contents of both bottles into the reservoir. Start with five strokes at each wheel until you see how much fluid is being forced through, so you equally balance the flushing from front to rear.
Contaminated brake fluid is corrosive and damaging to all the internal brake-system components, and it can cause poor braking performance. Even though every manufacturer specifies to flush it on a regular basis, it’s still out-of-sight, out-of-mind for a lot of people. In my opinion, you can’t change the brake fluid too often.
A complete brake job not only includes fluid, but also calipers or wheel cylinders in any situation where the bleeders don’t open.
Pads and Rotors
When disc brakes are being serviced, pads and rotors are at the core of the job. It’s far less common to resurface rotors than it has been in past times, and it doesn’t matter if you take that road or go with new. But the bottom line is something must happen with the rotors. “Slapping” a set of pads on old rotors is an immediate fail. The pads will never bed in properly, and you’ll only be faced with poor brake performance, uneven pad wear and unwanted noise.
The bottom line: Rotors must be resurfaced or replaced for the job to be complete. By the same token, old pads on new rotors equals an incomplete brake job.
Why would someone do this? Your guess could be as good as mine, but believe me, I’ve seen it all and I’m sure you have too. New pads and rotors bed in together. In other words, they rely on each other for proper brake operation.
Drum Brakes
If you thought there were some offenders with disc brakes, drums are often worse. For some reason there seems to be a perception that brake drums miraculously never need service, but the same theories hold true. If you’re replacing brake shoes, the job is only correctly done by resurfacing or replacing the drums.
Hardware
Hardware is anything from springs and hold-downs on drum brakes to anti-rattle clips and slide-pin boots on disc brakes. All these little pieces are important to proper brake operation. On drum brakes, even though everything may be intact, it’s also old and the springs will simply be fatigued. On disc brakes, the same holds true and even anti-rattle clips that look OK can be worn or fatigued in some manner. Luckily, most pads come with the hardware. They don’t put it in the box just for fun.
One of the most overlooked parts of disc-brake service is the fact that the pads must be able to move freely in the caliper bracket and the calipers also must be able to move freely back and forth. Most calipers (excluding fixed calipers) feature slide pins that allow this to happen. No brake job is complete without removing the slide pins, cleaning them up, lubricating them and reinstalling them with new boots when required.
It’s surprising how often the slide pins are stuck and how often brake pads are jammed in place due to rust, and the rust must be completely removed to allow free movement of the new brake pads. Stuck pins or stuck pads cause uneven and accelerated wear, dragging brakes, pulling and excessive heat buildup.
Lubrication
I touched on it already, but it’s worth a second mention. In addition to the slide pins on calipers, the brake pads require lubrication any place they contact the caliper bracket or caliper. Brake lube is specifically formulated to a) not damage or swell rubber components such as piston or slide-pin boots, b) prevent vibrations that cause noise, c) lubricate the pad contact points so they move freely in the caliper bracket and d) resist washing out.
In the case of drum brakes, the backing plates feature specific contact points for the brake shoes, which should be cleaned and lubricated. Brake shoes also require lubrication at pivot and contact points between the shoes and hardware.
Inspection
Determining what is required for a complete brake job can only be done through inspection and disassembly. It’s easy to see worn-out pads and rusty rotors through a wheel, but even when that’s evident, you can’t see anything else until you take things apart. This is when you inspect for brake-fluid leaks, seized or damaged hardware, torn dust boots and functional bleeder screws.
If leaks are found or dust boots are torn on a caliper piston or wheel cylinder, or if the bleeder won’t open, the components need to be replaced. Only until disassembly is performed during an inspection can you say absolutely what’s needed for any given vehicle. Sure, we can all look at a 50,000-mile four-year-old vehicle and say that it needs pads and rotors, and most likely those are the only hard parts it will need. But it’s no guarantee, and the higher the mileage and older the vehicle, the more likely we’ll find something else, which leads to the next category …
Recommending Parts
There’s always a way to work into the conversation of a complete brake job. The next time someone comes in and wants pads and rotors, you might ask, “Would you like me to look up caliper availability just in case a bleeder screw doesn’t open, or a caliper pin is seized?” If they’re an experienced technician, they know how often that happens, and they’ll likely say yes, just to know in case they need them, and they’ll appreciate it!
If they’re new at all this, it will get them thinking and open the door for your advice. The next thing you know, they might change their mind and decide to buy new calipers – or at minimum they’ll leave with the extra goodies they need for a complete brake job, such as brake lubricant, brake fluid, brake cleaner and some shop rags. If they get into the job and realize there’s a problem, they’ll be right back at your store.
The post
link hidden, please login to view appeared first on link hidden, please login to view.
link hidden, please login to view -
By Counterman
Performance Ride Technology (PRT) said it has launched 22 new complete strut assemblies providing coverage for 12 million vehicles in the North American market.
The strut assemblies are for popular models such as the Honda Civic, Jeep Cherokee and Toyota Highlander, in addition to brand-new applications such as the 2021 Subaru Forester, the 2021 Toyota Corolla and the 2021 Honda Accord Hybrid, among others.
PRT is a brand of the ADD Group, one of the largest manufacturers of complete strut assemblies in the world.
PRT products are manufactured under the strictest OE quality processes required by the major automakers, according to the company.
“As an OE supplier, our company is always focused on the continuous development of new products that stay ahead in aftermarket technology,” said Bruno Bello, director of global marketing at PRT.
“These new additions not only expand our product coverage but also strengthen our presence in the North American Aftermarket. The new items are in stock and ready to ship.”
For more information, call 770-238-1611 or visit
link hidden, please login to view. The post
link hidden, please login to view appeared first on link hidden, please login to view.
link hidden, please login to view -
By Counterman
PRT Heavy Duty is exhibiting its full line of shocks and air springs for heavy-duty applications in Booth 1417 at Heavy Duty Aftermarket Week (HDAW) ’24.
HDAW ’24 – the largest North American gathering of heavy-duty aftermarket professionals in the industry – runs from Jan. 22-25 at the Gaylord Hotel & Convention Center in Grapevine, Texas.
PRT Heavy Duty is a brand of the ADD Group, one of the largest manufacturers of shock absorbers and air springs for HD applications in the world.
PRT is showcasing its 100% gas-charged shocks that cover more than 5,000 OE references for trucks, trailers, buses, commercial vehicles, motorhomes, pickups and cargo vans.
Another highlight is its line of PRT HD air springs, which are made with OE-quality materials and premium rubber mixtures, “guaranteeing a maintenance-free and long-lasting product.”
“We are more than happy to present this extensive portfolio of HD shocks and air springs to our clients at HDAW 2024,” said Bruno Bello, director of global marketing at PRT. “PRT Heavy Duty is synonymous with performance, technology and leading coverage.”
For more information, call 770-238-1611 or visit
link hidden, please login to view. The post
link hidden, please login to view appeared first on link hidden, please login to view.
link hidden, please login to view -
By Counterman
PRT announced that it has introduced seven new complete strut assemblies representing nearly 4 million vehicles in additional coverage in North America.
The strut assemblies cover popular models such as the BMW 3 Series and Subaru Legacy, in addition to brand-new applications such as the 2022 Chevrolet Malibu, 2019 Kia Soul and 2019 Cadillac ATS, among others.
PRT is a brand of the ADD USA group, one of the largest manufacturers of complete strut assemblies in the world.
PRT products are manufactured under the strictest OE-quality processes required by the major automakers, according to the company.
“Our highly automated factories supply premium-quality products for the OE and aftermarket, focusing on innovation and advanced solutions,” said Bruno Bello, director of global marketing at PRT.
“PRT is always dedicated to the constant development of new products that stay ahead in aftermarket technology. These additions not only expand our product range but also strengthen our presence in the North American aftermarket. The new items are in stock and ready to ship.”
For more information, call 770-238-1611 or visit
link hidden, please login to view. The post
link hidden, please login to view appeared first on link hidden, please login to view.
link hidden, please login to view 
-
By Lon3_Sol_001
If anyone could help find quality performant brake kits, or list of parts for drum and disk brakes that are decently affordable for my 1985 S-10 it would be much appreciated
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.