Jump to content

  • Welcome to Auto Parts Forum

    Whether you are a veteran automotive parts guru or just someone looking for some quick auto parts advice, register today and start a new topic in our forum. Registration is free and you can even sign up with social network platforms such as Facebook, X, and LinkedIn. 

     

How To Test Coolant And Coolant Sensors

NAPA

By NAPA
in Napa Auto Parts Forum

 Share

Recommended Posts

NAPA Contributor

NAPA

Posted
Posted

Engine coolant keeps the waste heat of the combustion process at bay. There’s no denying the importance coolant plays in keeping an engine running, but how do you know when it needs to be changed? But also to make sure your coolant is doing its job it needs to be monitored by a coolant sensor. Let’s look at how to test engine coolant, how to pressure test a cooling system, and equally important how to test coolant temp sensor operation. 

Why Test Engine Coolant?

Your engine coolant is part of an enclosed system, but that system consists of many components of varying materials. Over time under the stress of extreme heat exposure the coolant loses some of its ability to control and conduct those temperatures. There are also parts of the cooling system that can corrode internally leaving tiny rust flakes that act like silty mud. There are all reasons why your engine coolant needs to be tested and periodically replaced when it has reached the end of its service life. But you need to test not only for the right coolant mixture ratio, but also the chemical composition of the coolant.

Testing Engine Coolant Ratio
link hidden, please login to view

The easiest way to test coolant mixing ratio with an

link hidden, please login to view
r. This neat little device tests the specific gravity of the coolant using either little colored floating balls or a swing arm. The balls and swing arm are calibrated to float at different levels based on the specific gravity of the coolant. Simply draw coolant into the antifreeze tester and compare the results to the included chart. Typically on a floating ball type tester the higher the concentration of ethylene glycol, the more balls that float. You can then estimate the freezing point of the coolant and how well you are protected against the cold. Just be aware that there are different testers for propylene glycol and ethylene glycol, so choose a tester that matches what is used in your cooling system.

For a more accurate measurement of your coolant’s freezing point you can use a refractometer. There are

link hidden, please login to view
and
link hidden, please login to view
refractometers but they both work on the same idea. Simply place a few sample drops of coolant in the tool. For the analog refractometer you then look through the eyepiece and read the inside gauge. For the digital refractometer you just have to push a button and the reading will be displayed on the screen. You will need to read the instructions and be familiar with the tool to understand what the results of each one means to the specific gravity of your coolant.

Testing Engine Coolant Condition

As mentioned earlier your coolant can actually degrade over time. Luckily a simple

link hidden, please login to view
can give you a glimpse of what is in your coolant. When the engine is cool and depressurized (never work on a hot engine’s cooling system) just remove the radiator cap and dip in a testing strip. Make sure to read the directions included with the testing strip to make sure you get a good reading. Most test strips can tell you the pH level, nitrate concentration level, and liquid freeze point. If any of these readings are out of specification, it is time for a
link hidden, please login to view
and refill. 

How To Test A Coolant Temp Sensor

Knowing how to test coolant temp sensor output is a bit more technical. You will need a multimeter to read the resistance of the coolant temp sensor during the test. You will also need to remove the coolant temp sensor from your vehicle, so refer to a repair manual for the specific procedure. For sensor range testing you will need a container of ice water and a container of boiling water. Finally you need the factory sensor range specifications (usually found in the repair manual) along with a pen and paper to take notes.

Once you have the sensor out of the vehicle attach it to the connections on the multimeter. Most sensors have two connections and since you are testing resistance, it does not matter which order is used. If your sensor has more than two connections refer to a vehicle wiring diagram to find the ground connection and the voltage input connection. 

You will be testing engine coolant temperature sensor resistance output in cold water and hot water, then comparing the two readings to the factory specification found in your repair manual. Check the temperature of the ice water to make sure it is as close to freezing as possible (32 degrees F or 0 degrees C). Set the voltmeter to the 20,000 ohm range. Dip the tip of the sensor in the cold water and observe the reading on the multimeter. When the reading stops changing, write it down on the paper as the cold reading. Repeat the same process with the boiling water, being careful to hold the sensor with tongs or similar tool to reduce the chance of touching the boiling water. Write down the hot temperature reading from the multimeter. 

Now you can compare the two voltage readings to the factory sensor specifications. If the readings are not within specifications the sensor is bad and should be replaced. Now that you know the steps for how to test an engine coolant temperature sensor, you can decide if it is worth your time or if the sensor is cheap enough to just replace it and move on.

How To Pressure Test A Coolant System

Luckily learning how to pressure test coolant system components is pretty easy. You will need an

link hidden, please login to view
which looks like a bicycle tire pump attached to a universal radiator cap. Start with a cool engine (never work on a hot engine cooling system under pressure). Remove the radiator cap or coolant reservoir cap if so equipped. Attach the pressure tester to the same place where you just removed the radiator cap or reservoir cap. The pressure tester may have a universal rubber fitting or come with an array of adapters to connect with your particular cooling system. Now use the pump to add pressurized air to the cooling system. Watch the pressure gauge on the pressure tester and add roughly 15 psi of pressure (but no more than that). The pressure gauge should hold steady indicating no leaks. If the pressure gauge goes down or does not register any pressure, double check your pressure tester connection just in case. If the system will not hold pressure, you will need to repair the leak. You can use
link hidden, please login to view
to help locate the leak if it is not easily apparent.

Check out all the

link hidden, please login to view
available on
link hidden, please login to view
or trust one of our 17,000
link hidden, please login to view
for routine maintenance and repairs. For more information on how to test engine coolant sensor output and other cooling system parts, chat with a knowledgeable expert at your
link hidden, please login to view
.

The post

link hidden, please login to view
appeared first on
link hidden, please login to view
.

link hidden, please login to view

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Dorman Products
      Rust Exhaust Hole | ASE Test Practice Question 3
      By Dorman Products
      Rust Exhaust Hole | ASE Test Practice Question 3
    • Garage Gurus
      Garage Gurus | How to Test Diesel Exhaust Fluid
      By Garage Gurus
      Garage Gurus | How to Test Diesel Exhaust Fluid
    • Dorman Products
      Brake Booster Valve | ASE Test Practice Question 2
      By Dorman Products
      Brake Booster Valve | ASE Test Practice Question 2
    • Counterman
      Why Does Engine Coolant Need Replacement?
      By Counterman
      On modern vehicles, overheating is a rare occurrence thanks to high-quality hoses, thermostats and better engine management. Unfortunately, the weak point is still the coolant. Whether it’s a 100,000-mile or 150,000-mile coolant, eventually it will break down and lose the ability to protect the components with which it comes into contact. 
      Coolant at 100,000 miles may look the same as coolant with zero miles, as the real difference between good and bad coolant can’t be seen with the naked eye; it is in the chemistry and based on mileage.
      Coolant contains additives called buffers that keep it at a neutral pH but these buffers are meant to last forever. When these chemicals become depleted, the pH can’t be controlled. It rises dramatically in a short period of time the moment the buffers are fully depleted. This is why replacing the coolant at the recommended interval is critical.
      Coolant has two specifications that can be used to justify replacement — the condition of the additive package and the freezing point.
      The additive package is the secret sauce for a coolant. Its main function is to control corrosion. Other components of the additive help with heat transfer and cavitation reduction. Some additive packages use seal conditioners to extend the life of the gaskets and plastic carriers.
      The freezing point is measured by the overall specific gravity of the coolant, which has a direct relationship to the coolant/water mixture. This test can help spot coolant that has been compromised by the owner topping off with water. This measurement works well on systems that do not have pressurized reservoirs.
      The strength or freezing point of coolant can be measured with a simple hydrometer. This device uses a calibrated float or plastic balls (not as accurate) to show the specific gravity of the coolant. This, in turn, shows how much freezing/boiling protection the coolant offers. You must remember to compensate for temperature because the specific gravity (density) of the coolant is lower when the coolant is hot.
      The more professional tool for this purpose is an optical refractometer because it is very accurate and automatically compensates for temperature. Be aware: these are not simple, inexpensive tools. A refractometer can cost up to $300 or more because of the precision optics in its lens. Ethylene glycol (EG) and polyethylene glycol (PG) antifreeze have slightly different densities, so you have to use a hydrometer or refractometer with the appropriate scale (or one with a dual scale) for accurate test results.
      Color-coded chemical test strips that are dipped into the coolant can be used to quickly and easily reveal the condition of the coolant. These strips of coated capillary paper react to the presence of certain dissolved minerals in the coolant and change color to give a good, marginal or bad indication of the coolant’s pH condition. Some test strips also show the concentration of antifreeze in the coolant. 
      The added benefit of test strips is that the results can be shared with the owner by attaching the used strip to the inspection form.
      But, mileage is the gold standard for any coolant replacement recommendation. Engineers and chemists spend a lot of time formulating the coolant to match the engine and interval.
      If you are performing a water pump, heater core or hose repair, recommend a full coolant flush. Just topping off the coolant can lead to a mixed bag when measuring the pH and freezing point. Also, check the specific gravity before a repair. Many customers know how to top off their coolant with water that could dilute the coolant concentration. 
      Selling any fluid maintenance service is difficult these days. But, if you document and educate customers on the importance of coolant, it becomes more than just an “add on” service.
      The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • A-premium Auto Parts:5% OFF with Code GM5.
    • Dorman Products
      Brake Rotor Thickness Variation | ASE Test Practice Question 1
      By Dorman Products
      Brake Rotor Thickness Variation | ASE Test Practice Question 1

×
×
  • Create New...