Welcome to Auto Parts Forum
Thanks for visiting our brand new online forum for automotive parts. We are just starting to build content and invite you to join us here in our new online discussion forum for automotive parts topics. Whether you are a veteran automotive parts guru or just someone looking for some quick auto parts advice, register today and start a new topic in our forum. Registration is free and you can even do it with social network platforms such as Facebook, Twitter, Google, and LinkedIn.
By 袁春凤 (Tiffany)
The most important component of the water pump is the pump shell and the inner parts of bearing and the bearing. To improve the pump, the most important thing is to optimize and improve the two parts. The following is a detailed introduction to the improvement of the two parts.
1. to improve the pump shell. When disassembly the pump to inspect the failure, there are a large number of debris seriously affect the quality of the pump and work efficiency. In this case, we can reduce the two holes used for drainage on the pump shell to one, and remove the drain holes on the upper part of the transmitter. This can greatly reduce the small particles and sundries into the pump, thus greatly reducing the interference of sundries on the pump and the other bad.
2. to improve the bearing. In the case of the failure of the bearing, we are generally sealed, the lubricating oil used by the bearing, the ball of the bearing and the bearing itself. So we should have a solution to these parts
3. to improve gasket. The traditional design is to design the sealing test as a double mouth seal, so the advantage of the design is that two ports are all frictional with the bearing, the roughness of the bearing surface is more appropriate and the wear of the lip is relatively slow; but the disadvantage is that a large amount of dust can be directly entered into the middle of the mouth and bearing, so that the plate will be used for a period of time. The interference between the bearing and the bearing decreases, thus losing the original function of the seal. There are two ways to improve it: the first is the sealing week of the bearing with double, and the sealing area is lengthened properly and the thickness of the chip mouth is thickened accordingly. The method is to change the original double mouth into the three form of the seal and seal the seal. The advantage of this structure is that the outer lip and mouth have increased the seal design, which can resist many dust. However, this method also has shortcomings, the mouth and the reverse cap friction, the surface roughness of the surface of the cover is relatively poor, it is very easy to wear and tear seal test, resulting in sealing failure.
4. to improve the lubricating oil. The bearing of the automobile pump is a more special bearing unit. Its environment is mostly temperature, humidity and dust, and the temperature of the water usually reaches about one thousand degrees, so the lubricating oil of the bearing is required. From our analysis of the fault, the lubricating oil in the bearing of the fault appears discolourable, which means that the grease in the lubricating oil is not enough, so the lubricating oil manufacturer should be required to increase the fat content of the lubricating oil so as to ensure the better protection of the bearing.
5. to Improve the contact ball of the bearing. Balls in bearing are important parts to ensure normal operation of bearings, but there are more and more damage to rolling balls. When measuring the hardness of the ball, it is found that most of the balls do not meet the required hardness requirements, which makes the bearings greatly wear at high speed and finally breaks down completely. Therefore, we should strictly supervise the production quality of the manufacturers, guarantee the hardness of the ball and pass the quality, so that the fundamental problem of bearing damage can be effectively solved.
By 袁春凤 (Tiffany)
Precautions for the installation of water pump
(1) the real reason for the damage of the water pump should be clearly defined. Before the pump is replaced, it is necessary to determine whether the radiator fan, the thermostat and the antifreeze are problematic.
(2) it is possible to have a water pump with similar shapes but only for different types of engines, so the new water pump should be compared with the old pump before the water pump is installed, or the part number of the pump and the model of the engine should be checked in order to confirm whether the selected water pump is suitable for the model.
(3) When installing the water pump, it is necessary to wet the pump sealant ring with coolant first. If you need sealant, be careful not to apply too much sealant. Do not apply grease for ease of installation. This will corrode the sealing ring and cause leakage of coolant.
(4) Do not use the method of percussion pump shaft forced installation of the water pump, should check the pump installation difficulties of the real reason. If the excessive scale in the cylinder water channel leads to the difficulty of pump installation, steel wire brush or fine sand paper should be selected according to the scale situation. When tightening the pump mounting bolts, it should be gradually tightened according to the prescribed torque according to the diagonal direction. Excessive tightening can easily break the bolt or cause damage to the gasket.
(5) it should be emphasized that the belt must be adjusted strictly according to the adjustment specifications for the need to adjust the tightness of the transmission belt. If the pump is damaged in a short period of time after the replacement of the new transmission belt, the tightness of the belt should be checked after removing the cause of the pump itself, and it should be checked whether the belt will always work in the same plane.
By 袁春凤 (Tiffany)
Perfect match of pump and thermostat
The engine is realized by the circulation of coolant. The component of the forced circulation of coolant is a water pump, which is driven by a crankshaft belt to promote the circulation of coolant throughout the system. Specializing in the production of water pumps for 40 years Feilongjiang Li's latest product - electric water pumps, it can accurately control the pump speed, and effectively reduce the loss of output power. The cooling of these coolants on the engine should be adjusted at any time according to the working conditions of the engine. When the engine temperature is low, the coolant circulates inside the engine itself. When the engine temperature is high, the coolant circulates between the engine and the radiator. The thermostat is used to control the coolant in different cycles. The thermostat can be regarded as a valve, its principle is to use materials that can be flexible with the temperature (paraffin or ether and so on) as a switch valve, when the water temperature is high material expansion top open valve, coolant for a large cycle, when the water temperature is low material shrinkage closed valve, coolant small cycle.
By Mengjuan Zhu
It is unavoidable that the breakdown of the automobile water pump is in use. Common faults are as follows:
（1） Bearing locking and fracture
The causes of bearing failure may be the following aspects: bearing itself quality defects; bearing excessive impact load; product structure design defects; improper pump installation (such as knocking installation, belt tension, etc.)
（2） Leakage of installation surface
The possible reasons for leakage of installation surface are as follows: uneven application of sealant, resulting in leakage of seam; improper installation of sealing gasket; leakage of pump sealing gasket or improper installation operation.
（3） Impeller damage
Impeller damage is common in the form of impeller cracking, impeller loose from the pump shaft or impeller corrosion, impeller corrosion will not generally cause engine failure. When the impeller cracks or the impeller is loosened from the pump shaft, the coolant circulation speed becomes slower, which may easily cause the engine temperature to be too high. Damaged impeller may also impact the pump housing when rotating, causing cracking.
If your car water pump is broken down , Feilong water pump can give you the prompt help.
By Erica Zhu Feilong Jiangli
We are auto water pumps manufacturer in Chongqing,China.Our parts are original with high quality. We accept custom.Our water pumps contain Ford, VW,GM,Audi ,etc.If you want to more information, you can look through the website https://cqfeilong.en.alibaba.com.